Regulation UN No. 87 (Rev.3)

Daytime running lamps

Consolidated up to 01 series dated: 15.10.19

Status table
... Contents a0c0
... Regulation a0c0
... 1. Scope a0c0
... 2. Definitions a0c0
... 3. Application for approval a0c0
... 4. Markings a0c0
... 5. Approval a0c0
... 6. General specifications a0c0
... 7. Intensity of light a0c0
... 8. Apparent surface a0c0
... 9. Colour of light a0c0
... 10. Test procedure a0c0
... 11. Heat resistance test a0c0
... 12. Modifications of a type of daytime running lamp and extension of approval a0c0
... 13. Conformity of production a0c0
... 14. Penalties for non-conformity of production a0c0
... 15. Production definitively discontinued a0c0
... 16. Names and addresses of Technical Services responsible for conducting approval tests, and of Type Approval Authorities a0c0
... Annexes a0c0
... 1 Communication a0c0
... 2 Example of arrangement of the approval mark a0c0
... 3 Photometric measurements a0c0
... 4 Minimum requirements for conformity of production control procedures a0c0
... 5 Minimum requirements for sampling by an inspector a0c0
... 6 Minimum angles required for light distribution in space a0c0
1. Scope a0c0
...

This Regulation applies to daytime running lamps for vehicles of category L, M, N and T [1].

 a0c0
[1] As defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3.), document ECE/TRANS/WP.29/78/Rev.2, para. 2. - www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html a0c0
2. Definitions a0c0
... For the purposes of this Regulation: a0c0
2.1. "Daytime running lamp" means a lamp or an interdependent lamp system facing in a forward direction used to make the vehicle more easily visible when driving during daytime; a1c0
2.2. The definitions given in Regulation No. 48 and its series of amendments in force at the time of application for type approval shall apply to this Regulation; a0c0
2.3. Daytime running lamps of different "types" means lamps [DEL]which differ in such essential respects as: a3c0
... (a)The trade name or mark: a3c0
... (i) Lamps bearing the same trade name or mark but produced by different manufacturers shall be considered as being of different types; a3c0
... (ii) Lamps produced by the same manufacturer differing only by the trade name or mark shall be considered as being of the same type. a3c0
... (b)The characteristics of the optical system, (levels of intensity, light distribution angles, category of light source, light source module, etc.); a1c0
... A change of the colour of the light source or the colour of any filter does not constitute a change of type. a1c0
2.4.

References made in this Regulation to standard (étalon) filament lamp(s) and to Regulation No. 37 shall refer to Regulation No. 37 and its series of amendments in force at the time of application for type approval.

 a0c0
...

References made in this Regulation to standard (étalon) LED light source(s) and to Regulation No. 128 shall refer to Regulation No. 128 and its series of amendments in force at the time of application for type approval.

 a0c0
3. Application for approval a0c0
3.1. The application for approval shall be transmitted by the holder of the trade name or mark or his duly accredited representative. a1c0
... At the choice of the applicant, it will specify that the daytime running lamp may be installed on the vehicle with different inclinations of the reference axis in respect to the vehicle reference planes and to the ground or rotate around its reference axis; these different conditions of installation shall be indicated in the communication form. a1c0
... All the interdependent lamps of an interdependent lamp system shall be submitted for type approval by the same applicant. a1c0
3.2. For each type of daytime running lamp, the application shall be accompanied by: a0c0
3.2.1.

Drawings (three copies) in sufficient detail to permit identification of the type of the daytime running lamp and showing geometrically the position(s) in which the daytime running lamp may be mounted on the vehicle, the axis of observation to be taken as the axis of reference in the tests (horizontal angle H=0°, vertical angle V=0°) and the point to be taken as the centre of reference in the said tests; and the illuminating surface,

 a0c0
3.2.2. A brief technical description stating, in particular, with the exception of daytime running lamps with non-replaceable light sources: a1c0
...

(a) The category or categories of filament lamp(s) prescribed; this filament lamp category shall be one of those contained in Regulation No. 37 and its series of amendments in force at the time of application for type approval; and/or

 a1c0
... (b)The category or categories of LED light source(s) prescribed; this LED light source category shall be one of those contained in Regulation No. 128 and its series of amendments in force at the time of application for type approval; and/or a1c0
... (c)The light source module specific identification code. a1c0
3.2.3. Two daytime running lamps. a1c0
3.2.4. In the case of a type of lamp differing only by the trade name or mark from a type that has already been approved it shall be sufficient to submit: a1c0
3.2.4.1. A declaration by the lamp manufacturer that the type submitted is identical (except in the trade name or mark) with and has been produced by the same manufacturer as, the type already approved, the latter being identified by its approval code; a1c0
3.2.4.2. Two samples bearing the new trade name or mark or equivalent documentation. a1c0
3.2.5. In the case of a non-replaceable filament lamp(s) or light source module(s) equipped with non-replaceable filament lamp(s), the documents according to paragraph 6.6. of this Regulation. a1c0
4. Markings a0c0
... Daytime running lamps submitted for approval shall: a0c0
4.1. Bear the trade name or mark of the applicant; this marking must be clearly legible and be indelible; a0c0
4.2. With the exception of daytime running lamps with non-replaceable light sources, bear a clearly legible and indelible marking indicating: a1c0
... (a)The category or categories of light source(s) prescribed; and/or a1c0
... (b)The light source module specific identification code. a1c0
4.3. In the case of lamps with an electronic light source control gear and/or non replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage.[DEL] a3c0
4.4. Provide adequate space for the approval mark and for the additional symbols prescribed in paragraph 5.2. below; the said space shall be shown in the drawings referred to in paragraph 3.2.1. above. a0c0
4.5. In the case of daytime running lamps with light source module(s), the light source module(s) shall bear: a1c0
4.5.1. The trade name or mark of the applicant; this marking must be clearly legible and indelible; a0c0
4.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 5.2.1.1. below and, in the case several non-identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 3.2.1. above. a0c0
... The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant. a0c0
4.5.3. The marking of the rated voltage or range of voltage. [DEL] a3c0
4.6.

Lamps operating at voltages other than the nominal rated voltages of 6 V, 12 V or 24 V respectively, by the application of an electronic light source control gear being not part of the lamp, must also bear a marking denoting the rated secondary design voltage.

 a0c0
4.7. An electronic light source control gear being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number. a0c0
5. Approval a0c0
5.1. General a0c0
5.1.1. If the two daytime running lamps which are submitted in pursuance of paragraph 3.2.3. above satisfy the requirements to this Regulation, approval shall be granted. a0c0
5.1.2.

Where grouped, combined or reciprocally incorporated lamps have been found to comply with the requirements of several Regulations annexed to the 1958 Agreement, a single international approval mark may be applied provided that such lamps are not grouped, combined or reciprocally incorporated with a lamp or lamps not satisfying any one of these Regulations.

 a0c0
5.1.3. An approval number shall be assigned to each type approved. Its first two digits (at present 00 for the Regulation in its original form) shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval. The same Contracting Party shall not assign this number to another type of daytime running lamp covered by this Regulation. a1c0
5.1.4. Notice of approval or of extension or refusal or withdrawal of approval or production definitively discontinued of a type of daytime running lamp pursuant to this Regulation shall be communicated to the Parties to the Agreement which apply this Regulation, by means of a form conforming to the model in Annex 1 to this Regulation. a1c0
5.1.5. Every daytime running lamp conforming to a type approved under this Regulation shall bear, in the space referred to in paragraphs 4.4. above, an approval mark as described in paragraphs 5.2. and 5.3. below. a1c0
5.1.6. The mark and symbols mentioned in paragraph 5.2. below shall be indelible and clearly legible even when the daytime running lamp is mounted on the vehicle. a1c0
5.2. Composition of the approval mark a0c0
... The approval mark shall consist of: a0c0
5.2.1. An international approval marking, comprising: a0c0
5.2.1.1. A circle surrounding the letter "E" followed by the distinguishing number of the country which has granted the approval;[2] a0c0
[2] The distinguishing numbers of the Contracting Parties to the 1958 Agreement are reproduced in Annex 3 to the Consolidated Resolution on the Construction of Vehicles (R.E.3), document ECE/TRANS/WP.29/78/Rev.2/Amend.3 - www.unece.org/trans/main/wp29/wp29wgs/wp29gen/wp29resolutions.html a0c0
5.2.1.2. An approval number; a0c0
5.2.2. The additional symbol "RL" and a1c0
5.2.2.1 An additional letter "Y" to the right on each interdependent lamp which may be used as part of an interdependent lamp system. a1c0
5.2.3. The two digits of the approval number which indicate the series of amendments in force at the time of issue of the approval, may be marked close to the above additional symbols. a0c0
5.3. Arrangement of the approval mark a0c0
5.3.1. Independent lamps a0c0
... Annex 2, Figure 1, to this Regulation gives an example of arrangement of the approval mark with the above-mentioned additional symbols. a0c0
5.3.2. Grouped, combined or reciprocally incorporated lamps a0c0
5.3.2.1. Where grouped, combined or reciprocally incorporated lamps have been found to comply with the requirements of several Regulations, a single international approval mark may be affixed, consisting of a circle surrounding the letter "E" followed by the distinguishing number of the country which has granted the approval, and an approval number. This approval mark may be located anywhere on the grouped, combined or reciprocally incorporated lamps, provided that: a0c0
5.3.2.1.1. It is visible after their installation. a0c0
5.3.2.1.2. No part of the grouped, combined or reciprocally incorporated lamps that transmits light can be removed without at the same time removing the approval mark. a0c0
5.3.2.2. The identification symbol for each lamp appropriate to each Regulation under which approval has been granted, together with the corresponding series of amendments incorporating the most recent major technical amendments to the Regulation at the time of issue of the approval and, if necessary, the required arrow shall be marked: a0c0
5.3.2.2.1. Either on the appropriate illuminating surface, a0c0
5.3.2.2.2. Or in a group, in such a way that each of the grouped, combined or reciprocally incorporated lamps may be clearly identified. a0c0
5.3.2.3. The size of the components of a single approval mark shall not be less than the minimum size required for the smallest of the individual marks by the Regulation under which approval has been granted. a0c0
5.3.2.4. An approval number shall be assigned to each type approved. The same Contracting Party may not assign the same number to another type of grouped, combined or reciprocally incorporated daytime running lamps covered by this Regulation. a1c0
5.3.2.5. Annex 2, Figure 2, to this Regulation gives examples of arrangements of approval marks for grouped, combined or reciprocally incorporated lamps with all the above-mentioned additional symbols. a0c0
5.3.3. Lamps reciprocally incorporated with other lamps, of which the lens may also be used for other types of lamps . a1c0
... The provisions laid down in paragraph 5.3.2. above are applicable. a1c0
5.3.3.1. In addition, where the same lens is used, the latter may bear the different approval marks relating to the different types of headlamps or units of lamps, provided that the main body of the lamps, even if it cannot be separated from the lens, also comprises the space described in paragraph 4.4. above and bears the approval marks of the actual functions. a1c0
... If different types of lamps comprise the same main body, the latter may bear the different approval marks. a1c0
5.3.4. Interdependent lamps as part of an interdependent lamps system Annex 2, Figure 1a, to this Regulation gives an example of the arrangement of approval marks relating to the above case. a1c0
6. General specifications a0c0
... The requirements contained in sections 5. "General specifications" and 6. "Individual specifications" and in the Annexes referenced in the said sections of Regulations Nos. 48, 53 or 86, and their series of amendments in force at the time of application for the lamp type approval shall apply to this Regulation.
The requirements pertinent to each lamp and to the category/ies of vehicle on which the lamp is intended to be installed shall be applied, where its verification at the moment of lamp type approval is feasible. 		a3c0
6.1. Each daytime running lamp shall conform to the specifications set forth in the paragraphs below. An interdependent lamp system shall meet the requirements when all its interdependent lamps are operated together. a1c0
6.2. Daytime running lamps shall be so designed and constructed that in normal use, despite the vibration to which they may then be subjected, they continue to function satisfactorily and retain the characteristics prescribed by this Regulation. a0c0
6.3. In the case of light source modules, it shall be checked that: a0c0
6.3.1. The design of the light source module(s) shall be such as: a0c0
... (a)That each light source module can only be fitted in no other position than the designated and correct one and can only be removed with the use of tool(s); a0c0
... (b) If there are more than one light source module used in the housing for a device, light source modules having different characteristics cannot be interchanged within the same lamp housing. a0c0
... The light source module(s) shall be tamperproof. a0c0
6.3.3. A light source module shall be so designed that regardless of the use of tool(s), it shall not be mechanically interchangeable with any replaceable approved light source. a0c0
6.4. Daytime running lamps, which are reciprocally incorporated with another function, using a common light source, and designed to operate permanently with an electronic light source control gear to regulate the intensity of the light emitted, are permitted. a0c0
6.5. In the case of replaceable light source(s): a0c0
6.5.1. The daytime running lamp shall only be equipped with light source(s) approved according to Regulation No. 37 and/or Regulation No. 128, provided that no restriction on the use is made in Regulation No. 37 and its series of amendments in force at the time of application for type approval or in Regulation No. 128 and its series of amendments in force at the time of application for type approval. a4c0
6.5.2. The design of the daytime running lamp shall be such that the light sources can be fixed in no other position but the correct one. a1c0
6.6. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with non-replaceable filament lamp(s), the applicant shall annex to the type approval documentation a report (by the light source manufacturer indicated in the type approval documentation), acceptable to the Type Approval Authority, that demonstrates compliance of these non-replaceable filament lamp(s) with the requirements as specified in paragraph 4.11. of IEC 60809, Edition 3. a3c0
7. Intensity of light a0c0
7.1.

The luminous intensity of the light emitted by each daytime running lamp shall not be less than 400 cd in the axis of reference.

 a1c0
7.2. Outside the reference axis and within the angular fields defined in the arrangement diagram in Annex 6 to this Regulation, the intensity of the light emitted by each daytime running lamp shall: a1c0
7.2.1.

In each direction corresponding to the points in the table of standard light distribution reproduced in Annex 3 to this Regulation, be not less than the minimum specified in paragraph 7.1. above, multiplied by the percentage specified in the said table of the direction in question, and

 a0c0
7.2.2.

Not exceed 1,200 cd in any direction the daytime running lamp is visible.

 a1c0
7.3.

Moreover, throughout the field defined in the diagram in Annex 6, the intensity of the light emitted shall not be less than 1.0 cd.

 a1c0
7.4. Light source failure a1c0
7.4.1. In the case of a daytime running lamp containing more than one light source, the daytime running lamp shall comply with the minimum intensity required and the maximum intensity shall not be exceeded. a1c0
7.4.2. In case of failure of any one light source in a single lamp containing more than one light source, one of the following provisions shall apply: a1c0
... (a)The light intensity at the points of standard light distribution defined in Annex 3 to this Regulation shall be at least 80 per cent of the minimum intensity required, or a1c0
... (b)The light intensity in the axis of reference shall be at least 50 per cent of the minimum intensity required, provided that a note in the communication form states that the lamp is only for use on a vehicle fitted with an tell-tale indicating failure. a2c0
7.4.3. A group of light sources, wired so that the failure of any one of them causes all of them to stop emitting light, shall be considered to be one light source. a1c0
8. Apparent surface a1c0
...

The area of the apparent surface in the direction of the axis of reference of the daytime running lamp shall be not less than 25 cm2 and not more than 200 cm2.

 a1c0
9. Colour of light a0c0
... The colour of the light shall be white. It shall be measured under the conditions as prescribed in paragraph 10. below. a0c0
10. Test procedure a0c0
10.1. All measurements, photometric and colorimetric, when not supplied by an electronic light source control gear, shall be carried out with an uncoloured or coloured standard light source of the category prescribed for the daytime running lamp, supplied with the voltage: a1c0
... (a)In the case of filament lamps, that is necessary to produce the reference luminous flux required for that category of filament lamp; a1c0
...

(b)In the case of LED light sources of 6.75 V, 13.5 V or 28.0 V; the luminous flux value produced shall be corrected. The correction factor is the ratio between the objective luminous flux and the mean value of the luminous flux found at the voltage applied.

 a1c0
10.2. In the case of a system that uses an electronic light source control gear being part of the daytime running lamp[3], all measurements, photometric and colorimetric, shall be made applying at the input terminals of the lamp a voltage of 6.75 V, 13.5 V or 28.0 V respectively. a1c0
[3] For the purpose of this Regulation, "being part of the lamp" means to be physically included in the lamp body or to be external, separated or not, from the lamp body but supplied by the lamp manufacturer as part of the lamp system. a0c0
10.3. In the case of a system that uses an electronic light source control gear not being part of the daytime running lamp the voltage declared by the manufacturer shall be applied to the input terminals of the daytime running lamp. The test laboratory shall require from the manufacturer the light source control gear needed to supply the light source and the applicable functions. a1c0
...

The voltage to be applied to the daytime running lamp shall be noted in the communication form in Annex 1 to this Regulation.

 a1c0
10.4.

For any daytime running lamp except those equipped with filament lamps, the luminous intensities, measured after one minute and after 30 minutes of operation, shall comply with the minimum and maximum requirements. The luminous intensity distribution after one minute of operation can be calculated from the luminous intensity distribution after 30 minutes of operation by applying at each test point the ratio of luminous intensities measured at HV after one minute and after 30 minutes of operation.

 a1c0
10.5. The limits of the apparent surface in the direction of the reference axis of a light-signalling device shall be determined. a0c0
11. Heat resistance test a0c0
11.1.

The daytime running lamp shall be subjected to a one-hour test of continuous operation following a warm-up period of 20 minutes. The ambient temperature shall be 23 °C + 5°. The light source used shall be a light source of the category specified for the daytime running lamp, and shall be supplied with a current at a voltage such that it gives the specified average power at the corresponding test voltage. However, for daytime running lamps equipped with non-replaceable light sources (filament lamps and other), the test shall be made with the light sources present in the daytime running lamp, in accordance with paragraph 10.2. of this Regulation.

 a1c0
11.2.

Where only the maximum power is specified, the test shall be carried out by regulating the voltage to obtain a power equal to 90 per cent of the specified power. The specified average or maximum power referred to above shall in all cases be chosen from the voltage range of 6,12 or 24 V at which it reaches the highest value; for daytime running lamps equipped with non-replaceable light sources (filament lamps and other) the test conditions set in paragraph 10.2. of this Regulation shall be applied.

 a1c0
11.3.

After the daytime running lamp has been stabilized at the ambient temperature, no distortion, deformation, cracking or colour modification shall be perceptible. In case of doubt the intensity of light according to paragraph 7. above shall be measured. At that measurement the values shall reach at least 90 per cent of the values obtained before the heat resistance test on the same device.

 a1c0
12. Modifications of a type of daytime running lamp and extension of approval a0c0
12.1. Every modification of the type of daytime running lamp shall be notified to the Administrative Departments which approved the type of daytime running lamp. The department may then either: a1c0
12.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the daytime running lamp still complies with the requirements; or a1c0
12.1.2. Require a further test report from the Technical Service responsible for conducting the tests. a0c0
12.2. Confirmation or refusal of approval, specifying the alterations shall be communicated by the procedure specified in paragraph 5.1.4. above to the Parties to the Agreement applying this Regulation. a0c0
12.3.

The Type Approval Authority issuing the extension of approval shall assign a series number for such an extension and inform thereof the other Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

 a0c0
13. Conformity of production a0c0
... The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2), with the following requirements: a0c0
13.1. Daytime running lamps shall be so manufactured as to conform to the type approved under this Regulation.
The compliance with the requirements set forth in paragraphs 6., 7., 8. and 9. above shall be verified as follows: 		a3c0
13.1.1. The minimum requirements for conformity of production control procedures set forth in Annex 4 to this Regulation shall be complied with. a3c0
13.1.2. The minimum requirements for sampling by an inspector set forth in Annex 5 to this Regulation shall be complied with. a3c0
13.2. The Type Approval Authority which has granted type approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verifications shall be once every two years. a3c0
13.3. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with non-replaceable filament lamps, a report (by the light source manufacturer indicated in the type approval documentation) shall demonstrate compliance of these non-replaceable filament lamp(s) with lifetime requirements and, in the case of colour coated filament lamps, also with colour endurance requirements, as specified in paragraph 4.11. of IEC 60809, Edition 3. a3c0
14. Penalties for non-conformity of production a0c0
14.1. The approval granted in respect of a type of daytime running lamp pursuant to this Regulation may be withdrawn if the requirements are not complied with or if a daytime running lamp bearing the approval mark does not conform to the type approved. a0c0
14.2.

If a Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith so notify the other Contracting Parties applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

 a0c0
15. Production definitively discontinued a0c0
...

If the holder of the approval completely ceases to manufacture a type of daytime running lamp approved in accordance with this Regulation, he shall so inform the Type Approval Authority which granted the approval. Upon receiving the relevant communication, that Authority shall inform thereof the other Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

 a0c0
16. Names and addresses of Technical Services responsible for conducting approval tests, and of Type Approval Authorities a0c0
... The Parties to the Agreement applying this Regulation shall communicate to the United Nations Secretariat the names and addresses of the Technical Services responsible for conducting approval tests and of the Type Approval Authorities which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, or production definitively discontinued, issued in other countries, are to be sent. a0c0
A1  Annex 1 a0c0
A1  Communication a0c0
A1  (Maximum format: A4 (210 x 297 mm)) a0c0
A1  a0c0
A1  of a type of daytime running lamp pursuant to Regulation No. 87 a0c0
A1 
Approval No....................................... Extension No.............................................
a0c0
A1 1. Trade name or mark of the daytime running lamp: a1c0
A1 2.

Manufacturer's name for the type of daytime running lamp:

 a1c0
A1 3.

Manufacturer's name and address:

 a0c0
A1 4. If applicable, name and address of manufacturer's representative: a0c0
A1 5. Submitted for approval on: a0c0
A1 6. Technical Service responsible for conducting approval tests: a0c0
A1 7. Date of report issued by that Service: a0c0
A1 8. Number of report issued by that Service: a0c0
A1 9. Concise description: a0c0
A1  By category of lamp: a0c0
A1  Number, category and kind of light source(s):[3] a0c0
A1  Voltage and wattage: a0c0
A1  Application of an electronic light source control gear: a0c0
A1  (a)Being part of the lamp: Yes/No [2] a0c0
A1  (b)Being not part of the lamp: Yes/No [2] a0c0
A1  Input voltage supplied by an electronic light source control gear: a0c0
A1  Electronic light source control gear manufacturer and identification number (when the light source control gear is part of the lamp but is not included into the lamp body): a0c0
A1  The lamp is only for use on a vehicle fitted with a tell-tale indicating failure: yes/no[2] a2c0
A1 10. The daytime running lamp is designed as an interdependent lamp system yes/no[2] a1c0
A1  The interdependent lamp system consists of 2/3[2] interdependent lamps. a1c0
A1 11. Position of the approval mark: a1c0
A1 12. Reason(s) for extension (if applicable): a1c0
A1 13. Approval granted/refused/extended/withdrawn:[2] a1c0
A1 14. Place: a1c0
A1 15. Date: a1c0
A1 16. Signature: a1c0
A1 17. The following documents, bearing the approval number shown above, are available on request: a1c0
A1 [1]

Distinguishing number of the country which has granted/refused/withdrawn approval (see approval provisions in the Regulation).

 a0c0
A1 [2] Strike out which does not apply. a0c0
A1 [3] For daytime running lamps with non-replaceable light sources indicate the number and total wattage of the light sources used. a0c0
A2  Annex 2 a0c0
A2  Example of arrangement of the approval mark a0c0
A2  Figure 1 a0c0
A2  a0c0
A2  The daytime running lamp bearing the approval mark shown above has been approved in the Netherlands (E 4) under number 001015. The approval number indicates that the approval was granted according to the requirements of this Regulation in its original (unamended) form. a0c0
A2  Note: The approval number and the additional symbol must be placed close to the circle and either above or below the "E" or to the left or right of that letter. The digits of the approval number must be on the same side of the "E" and face the same direction. The use of roman numerals as approval numbers should be avoided so as to prevent any confusion with other symbols. a0c0
A2  Figure 1a a1c0
A2  a1c0
A2  The lamp bearing the approval mark shown above has been approved in the Netherlands (E 4) under number 001015 as a part of an interdependent lamp system composing a daytime running lamp. The approval number indicates that the approval was granted according to the requirements of this Regulation in its original (un-amended) form. a1c0
A2  Figure 2 a0c0
A2  Examples of possible markings for grouped lamps situated at the front of the vehicle a0c0
A2  The vertical and horizontal lines schematize the shape of the lighting device. These are not part of the approval mark. a0c0
A2  a0c0
A2  Note: The three examples shown above correspond to a lighting device bearing an approval mark relating to: a0c0
A2 

A front position lamp approved in accordance with the 01 series of amendments to Regulation No. 7;

 a0c0
A2  A headlamp with a passing-beam designed for right-hand and left-hand traffic and a driving-beam with a maximum intensity comprised between 86,250 and 101,250 candelas, approved in accordance with the 02 series of amendments to Regulation No. 8; a0c0
A2  A daytime running lamp approved in accordance with Regulation No. 87 in its original form; a0c0
A2  A front direction indicator lamp of category la approved in accordance with the 02 series of amendments to Regulation No. 6. a0c0
A2  Figure 3 a0c0
A2  Lamp reciprocally incorporated with a headlamp a0c0
A2  a0c0
A2  The above example corresponds to the marking of a lens intended to be used in different types of headlamps, namely: a0c0
A2  either: a0c0
A2  a headlamp with a passing-beam designed for right-hand and left-hand traffic and a driving-beam with a maximum intensity comprised between 86,250 and 101,250 candelas, approved in Germany (E 1) in accordance with the requirements of Regulation No. 8 as amended by the 02 series of amendments, a0c0
A2 

which is reciprocally incorporated with a daytime running lamp approved in accordance with Regulation No. 87 in its original form;

 a0c0
A2  or: a0c0
A2  a headlamp with a passing-beam designed for right-hand and left-hand traffic and a driving-beam, approved in Germany (E 1) in accordance with the requirements of Regulation No. 1 as amended by 01 series of amendments, a0c0
A2  which is reciprocally incorporated with the same daytime running lamp as above; a0c0
A2  or even: a0c0
A2  either of the above-mentioned headlamps approved as a single lamp. a0c0
A2  The main body of the headlamp shall bear the only valid approval number, for instance: a0c0
A2  a0c0
A3  Annex 3 a0c0
A3  Photometric measurements a0c0
A3 1. When photometric measurements are taken, stray reflections shall be avoided by appropriate masking. a0c0
A3 2. In the event that the results of measurements are challenged, measurements shall be taken in such way as to meet the following requirements: a0c0
A3 2.1. The distance of measurement shall be such that the law of the inverse of the square of the distance is applicable: a0c0
A3 2.2.

The measuring equipment shall be such that the angle subtended by the receiver from the reference centre of the light is between 10' and 1°:

 a0c0
A3 2.3. The intensity requirement for a particular direction of observation shall be satisfied if the required intensity is obtained in a direction deviating by not more than one-quarter of a degree from the direction of observation. a0c0
A3 3. In the case where the daytime running lamp may be installed on the vehicle in more than one or in a field of different positions the photometric measurements shall be repeated for each position or for the extreme positions in the field of the reference axis specified by the manufacturer. a0c0
A3 4. Photometric measurement of daytime running lamps a1c0
A3  The photometric performance shall be checked: a1c0
A3 4.1. For non-replaceable light sources (filament lamps or other): a1c0
A3 

with the light sources present in the daytime running lamp, in accordance with paragraph 10. of this Regulation.

 a1c0
A3 4.2. For replaceable filament lamps: a1c0
A3 

When equipped with filament lamps at 6.75 V, 13.5 V or 28.0 V the luminous intensity values produced shall be corrected. [DEL]The correction factor is the ratio between the reference luminous flux and the mean value of the luminous flux found at the voltage applied (6.75 V, 13.5 V or 28.0 V). ???Perché é stata rimossa la R128

 a1c0
A3  [DEL] a1c0
A3 

The actual luminous fluxes of each filament lamp used shall not deviate more than  5 per cent from the mean value. Alternatively standard filament lamp(s) may be used in turn, in each of the individual positions, operated at its reference flux, the individual measurements in each position being added together.

 a1c0
A3 4.3.

For any daytime running lamp except those equipped with filament lamp(s), the luminous intensities, measured after one minute and after 30 minutes of operation, shall comply with the minimum and maximum requirements. The luminous intensity distribution after one minute of operation can be calculated from the luminous intensity distribution after 30 minutes of operation by applying at each test point the ratio of luminous intensities measured at HV after one minute and after 30 minutes of operation.

 a0c0
A3 5. Table of standard light distribution a0c0
A3  a0c0
A3 5.1.

The direction H = 0° and V = 0° corresponds to the reference axis. (On the vehicle, it is horizontal, parallel to the median longitudinal plane of the vehicle and oriented in the required direction of visibility). It passes through the centre of reference. The values shown in the table give, for the various directions of measurement, the minimum intensities as a percentage of the minimum required in the axis for each daytime running lamp (in the direction H=0° and V = 0°).

 a1c0
A3 5.2. Within the field of light distribution of paragraph 3. above schematically shown as a grid, the light pattern should be substantially uniform, i.e. in so far as the light intensity in each direction of a part of the field formed by the gird lines shall meet at least the lowest minimum value being shown on the gird lines surrounding the questioned direction as a percentage. a0c0
A3  Figure 4 a0c0
A3  Light source modules a0c0
A3  a0c0
A4  Annex 4 a0c0
A4  Minimum requirements for conformity of production control procedures a0c0
A4 1. General a0c0
A4 1.1. The conformity requirements shall be considered satisfied from a mechanical and geometric standpoint, if the differences do not exceed inevitable manufacturing deviations within the requirements of this Regulation. a0c0
A4 1.2. With respect to photometric performances, the conformity of mass-produced lamps shall not be contested if, when testing according to paragraph 10. of this Regulation, the photometric performances as set forth in paragraph 7. of this Regulation of any lamp chosen at random and equipped with a standard light source, or when the lamps are equipped with non-replaceable light sources (filament lamps or other), and when all measurements are made at 6.75 V, 13.5 V or 28.0 V respectively: a3c0
A4 1.2.1. No measured value deviates unfavourably by more than 20 per cent from the values prescribed in this Regulation. a3c0
A4 1.2.2. In the case of a lamp equipped with a replaceable light source, if results of the test described above do not meet the requirements, tests on lamps shall be repeated using another standard light source. a3c0
A4 1.3. The chromaticity coordinates shall be complied with when the lamp is equipped with a standard light source, or for lamps equipped with non- replaceable light sources (filament lamps or other), when the colorimetric characteristics are verified with the light source present in the lamp." a3c0
A4 2. Minimum requirements for verification of conformity by the manufacturer a0c0
A4  For each type of lamp the holder of the approval mark shall carry out at least the following tests, at appropriate intervals. The tests shall be carried out in accordance with the provisions of this Regulation. a0c0
A4  If any sampling shows non-conformity with regard to the type of test concerned, further samples shall be taken and tested. The manufacturer shall take steps to ensure the conformity of the production concerned. a0c0
A4 2.1. Nature of tests a0c0
A4  Tests of conformity in this Regulation shall cover the photometric and colorimetric characteristics. a0c0
A4 2.2. Methods used in tests a0c0
A4 2.2.1. Tests shall generally be carried out in accordance with the methods set out in this Regulation. a0c0
A4 2.2.2. In any test of conformity carried out by the manufacturer, equivalent methods may be used with the consent of the Type Approval Authority responsible for approval tests. The manufacturer is responsible for proving that the applied methods are equivalent to those laid down in this Regulation. a0c0
A4 2.2.3. The application of paragraphs 2.2.1. and 2.2.2. above requires regular calibration of test apparatus and its correlation with measurements made by a Type Approval Authority. a0c0
A4 2.2.4. In all cases the reference methods shall be those of this Regulation, particularly for the purpose of administrative verification and sampling. a0c0
A4 2.3. Nature of sampling a0c0
A4  Samples of lamps shall be selected at random from the production of a uniform batch. A uniform batch means a set of lamps of the same type, defined according to the production methods of the manufacturer. a0c0
A4  The assessment shall in general cover series production from individual factories. However, a manufacturer may group together records concerning the same type from several factories, provided these operate under the same quality system and quality management. a0c0
A4 2.4. Measured and recorded photometric characteristics a0c0
A4 

The sampled lamp shall be subjected to photometric measurements for the minimum values at the points listed in Annex 3 to this Regulation and the required chromaticity coordinates.

 a0c0
A4 2.5. Criteria governing acceptability a0c0
A4 

The manufacturer is responsible for carrying out a statistical study of the test results and for defining, in agreement with the Type Approval Authority, criteria governing the acceptability of his products in order to meet the specifications laid down for verification of conformity of products in paragraph 13.1. of this Regulation.

 a0c0
A4 

The criteria governing the acceptability shall be such that, with a confidence level of 95 per cent, the minimum probability of passing a spot check in accordance with Annex 5 (first sampling) would be 0.95.

 a0c0
A5  Annex 5 a0c0
A5  Minimum requirements for sampling by an inspector a0c0
A5 1. General a3c0
A5 1.1. The conformity requirements shall be considered satisfied from a mechanical and a geometric standpoint, in accordance with the requirements of this Regulation, if any, if the differences do not exceed inevitable manufacturing deviations. a3c0
A5 1.2. With respect to photometric performances, the conformity of mass-produced lamps shall not be contested if, when testing according to paragraph 10. of this Regulation, the photometric performances as set forth in paragraph 7. to this Regulation of any lamp chosen at random and equipped with a standard light source, or when the lamps are equipped with non-replaceable light sources (filament lamps or other), and when all measurements are made at 6.75 V, 13.5 V or 28.0 V respectively: a3c0
A5 1.2.1. According to the requirements in paragraph 1.2.1. of Annex 4 to this Regulation are met. a3c0
A5 1.2.2. In the case of a lamp equipped with a replaceable light source, if results of the test described above do not meet the requirements, tests on lamps shall be repeated using another standard light source. a3c0
A5 1.2.3. Lamps with apparent defects are disregarded. a3c0
A5 1.3. The chromaticity coordinates shall be complied with when the lamp is equipped with a standard light source, or for lamps equipped with non-replaceable light sources (filament lamps or other), when the colorimetric characteristics are verified with the light source present in the lamp. a3c0
A5 1.4. In the case of non-replaceable filament lamp(s) or light source module(s) equipped with non-replaceable filament lamps, at any conformity of production check: a3c0
A5 1.4.1. The holder of the approval mark shall demonstrate the use in normal production and show the identification of the non-replaceable filament lamp(s) as indicated in the type approval documentation; a3c0
A5 1.4.2. In the case where doubt exists in respect to compliance of the non-replaceable filament lamp(s) with lifetime requirements and/or, in the case of colour coated filament lamps, with colour endurance requirements, as specified in paragraph 4.11. of IEC 60809, Edition 3, conformity shall be checked (by the light source manufacturer indicated in the type approval documentation) as specified in paragraph 4.11. of IEC 60809, Edition 3. a3c0
A5 2. First sampling a3c0
A5  In the first sampling four lamps are selected at random. The first sample of two is marked A, the second sample of two is marked B. a3c0
A5 2.1. The conformity of mass-produced lamps shall not be contested if the deviation of any specimen of samples A and B (all four lamps) is not more than 20 per cent.
In the case, that the deviation of both lamps of sample A is not more than 0 per cent, the measurement can be closed. 		a3c0
A5 2.1.1. [DEL] a3c0
A5 2.1.1.1. [DEL] a3c0
A5 2.1.1.2. [DEL] a3c0
A5 2.1.2. [DEL] a3c0
A5 2.2. The conformity of mass-produced lamps shall be contested if the deviation of at least one specimen of sample A or B is more than 20 per cent.
The manufacturer shall be requested to bring his production in line with the requirements (alignment) and a repeated sampling according to paragraph 3. below shall be carried out within two months' time after the notification. The samples A and B shall be retained by the Technical Service until the entire Conformity of Production process is finished. 		a3c0
A5 2.2.1. [DEL] a3c0
A5 2.2.1.1. [DEL] a3c0
A5 2.2.1.2. [DEL] a3c0
A5 2.2.2. [DEL] a3c0
A5 2.3. [DEL] a3c0
A5 2.3.1. [DEL] a3c0
A5 2.3.2. [DEL] a3c0
A5 2.3.3. [DEL] a3c0
A5 3. First repeated sampling
A sample of four lamps is selected at random from stock manufactured after alignment.
The first sample of two is marked C, the second sample of two is marked D. 		a3c0
A5 3.1. The conformity of mass-produced lamps shall not be contested if the deviation of any specimen of samples C and D (all four lamps) is not more than 20 per cent.
In the case, that the deviation of both lamps of sample C is not more than 0 per cent, the measurement can be closed. 		a3c0
A5 3.1.1. [DEL] a3c0
A5 3.1.1.1. [DEL] a3c0
A5 3.1.1.2. [DEL] a3c0
A5 3.1.2. [DEL] a3c0
A5 3.2. The conformity of mass-produced lamps shall be contested if the deviation of at least a3c0
A5 3.2.1. One specimen of sample C or D is more than 20 per cent but the deviation of all specimen of these samples is not more than 30 per cent. The manufacturer shall be requested again to bring his production in line with the requirements (alignment).
A second repeated sampling according to paragraph 4. below shall be carried out within two months' time after the notification. The samples C and D shall be retained by the Technical Service until the entire Conformity of Production process is finished. 		a3c0
A5 3.2.1.1. [DEL] a3c0
A5 3.2.1.2. [DEL] a3c0
A5 3.2.2. One specimen of sample C or D is more than 30 per cent.
In this case the approval shall be withdrawn and paragraph 5. below shall be applied.
 a3c0
A5 3.3. [DEL] a3c0
A5 3.3.1. [DEL] a3c0
A5 3.3.2. [DEL] a3c0
A5 3.3.3. [DEL] a3c0
A5 4. Second repeated sampling
A sample of four lamps is selected at random from stock manufactured after alignment.
The first sample of two is marked E, the second sample of two is marked F. 		a3c0
A5 4.1. The conformity of mass-produced lamps shall not be contested if the deviation of any specimen of samples E and F (all four lamps) is not more than 20 per cent.
In the case, that the deviation of both lamps of sample E is not more than 0 per cent, the measurement can be closed. 		a3c0
A5 4.2. The conformity of mass-produced lamps shall be contested if the deviation of at least one specimen of sample E or F is more than 20 per cent.
In this case the approval shall be withdrawn and paragraph 5. below shall be applied. 		a3c0
A5 5. Approval withdrawn Approval shall be withdrawn according to paragraph 14. of this Regulation. a3c0
A5  [DEL] a3c0
A5  [DEL] a3c0
A6  Annex 6 a0c0
A6  Minimum angles required for light distribution in space a1c0
A6 

In all cases, the minimum vertical angles of light distribution in space are 10° above and 5° below the horizontal for the daytime running lamp included in the Regulation.

 a1c0
A6  Minimum horizontal angles of light distribution in space: a1c0
A6  a1c0